Surveiller ce forum | 
Commencer une nouvelle discussion
| TwainSane + Scanner Epson perfection 1250 [ Répondre ] Par : eric kobi on 2011-10-19 11:27 | [forum:476427] |
|
Bonjour, Voulant essayer la macro de Medintux pour scanner des documents directement dans Dr tux, j'ai installé la dernière version de TWAINSANE dans mon environnement MacOSX 10.6 sur IMac 21,5 Sur Sane le driver (Blackend) compatible avec mon vieux scanner Epson perfection 1250 est PLUSTEK Désolé d'intégrer ce post ici mais mes recherches sur le web restent vaines ... 1/ A priori, Sane retrouve mon scanner ... voici sur terminal le résultat de la commande : $ sane-find-scanner -q found USB scanner (vendor=0x04b8 [EPSON], product=0x010f [EPSON Scanner 010F], chip=LM983x?) at libusb:001:003-04b8-010f-ff-00 found USB scanner (vendor=0x05ac [Motorola, Inc.], product=0x1401 [Apple USB Modem]) at libusb:003:004-05ac-1401-ff-00 found USB scanner (vendor=0x05ac [Apple Inc.], product=0x8215 [Bluetooth USB Host Controller]) at libusb:003:006-05ac-8215-ff-01 Néanmoins, je trouve bizarre la présence du "?" dans l'identification du chipset ???? 2/ scanimage n'identifie pas mon scanner ... voici la réponse à la commande : $ scanimage -L No scanners were identified. If you were expecting something different, check that the scanner is plugged in, turned on and detected by the sane-find-scanner tool (if appropriate). Please read the documentation which came with this software (README, FAQ, manpages). 3/ Malgré de nombreux essais de configuration du fichier /usr/local/etc/saned/plustek.conf, scanimage reste en échec d'exécution voici ma configuration actuelle : [usb] 0x04b8 0x010f device /dev/usbscanner option lampOff 0 option warmup 180 option lOffOnEnd 0 # to enable TPA (EPSON or UMAX, if autodetection fails) # 0 means default behaviour as specified in the internal tables # 1 means enable (needed for UMAX 3450) option enableTPA 1 D'autres configurations avec échec d'exécution de scanimage : device auto ou device libuus:001:003 option enableTPA 0 4/ Pour info voici le DEBUG sorti avec la commande : $ SANE_DEBUG_PLUSTEK=20 scanimage> test.pnm [sanei_debug] Setting debug level of plustek to 20. [plustek] Plustek backend V0.52-9, part of sane-backends 1.0.21cvs [plustek] Retrieving all supported and conntected devices [plustek] Checking for 0x07b3-0x0010 [plustek] Checking for 0x07b3-0x0011 [plustek] Checking for 0x07b3-0x0013 [plustek] Checking for 0x07b3-0x0017 [plustek] Checking for 0x07b3-0x0015 [plustek] Checking for 0x07b3-0x0015 [plustek] Checking for 0x07b3-0x0017 [plustek] Checking for 0x07b3-0x0013 [plustek] Checking for 0x07b3-0x0011 [plustek] Checking for 0x07b3-0x0010 [plustek] Checking for 0x07b3-0x0014 [plustek] Checking for 0x07b3-0x0014 [plustek] Checking for 0x07b3-0x0016 [plustek] Checking for 0x07b3-0x0017 [plustek] Checking for 0x07b3-0x0017 [plustek] Checking for 0x07b3-0x0007 [plustek] Checking for 0x07b3-0x000f [plustek] Checking for 0x07b3-0x000f [plustek] Checking for 0x07b3-0x0005 [plustek] Checking for 0x07b3-0x0014 [plustek] Checking for 0x07b3-0x0012 [plustek] Checking for 0x0400-0x1000 [plustek] Checking for 0x0400-0x1001 [plustek] Checking for 0x0400-0x1001 [plustek] Checking for 0x0458-0x2007 [plustek] Checking for 0x0458-0x2008 [plustek] Checking for 0x0458-0x2009 [plustek] Checking for 0x0458-0x2013 [plustek] Checking for 0x0458-0x2015 [plustek] Checking for 0x0458-0x2016 [plustek] Checking for 0x03f0-0x0505 [plustek] Checking for 0x03f0-0x0605 [plustek] Checking for 0x04b8-0x010f [plustek] Checking for 0x04b8-0x011d [plustek] Checking for 0x1606-0x0050 [plustek] Checking for 0x1606-0x0060 [plustek] Checking for 0x1606-0x0160 [plustek] Checking for 0x049f-0x001a [plustek] Checking for 0x04a9-0x2206 [plustek] Checking for 0x04a9-0x2207 [plustek] Checking for 0x04a9-0x2208 [plustek] Checking for 0x04a9-0x220d [plustek] Checking for 0x04a9-0x220e [plustek] Checking for 0x04a9-0x2220 [plustek] Checking for 0x0a82-0x4600 [plustek] Checking for 0x0a82-0x6620 [plustek] Checking for 0x04a7-0x0427 [plustek] Checking for 0x0a53-0x1000 [plustek] Available and supported devices: [plustek] Device: >libusb:001:003-04b8-010f-ff-00< - 0x04b8x0x010f [plustek] ># Plustek-SANE Backend configuration file< [plustek] ># For use with LM9831/2/3 based USB scanners< [plustek] >#< [plustek] >< [plustek] ># each device needs at least two lines:< [plustek] ># - [usb] vendor-ID and product-ID< [plustek] ># - device devicename< [plustek] ># i.e. for Plustek (0x07B3) UT12/16/24 (0x0017)< [plustek] ># [usb] 0x07B3 0x0017< [plustek] ># device /dev/usbscanner< [plustek] ># or< [plustek] ># device libusb:bbb:ddd< [plustek] ># where bbb is the busnumber and ddd the device number< [plustek] ># make sure that your user has access to /proc/bus/usb/bbb/ddd< [plustek] >#< [plustek] ># additionally you can specify some options< [plustek] ># warmup, lOffOnEnd, lampOff< [plustek] >#< [plustek] ># For autodetection use< [plustek] ># [usb]< [plustek] ># device /dev/usbmodem< [plustek] >#< [plustek] ># or simply< [plustek] ># [usb]< [plustek] >#< [plustek] ># or if you want a specific device but you have no idea about the< [plustek] ># device node or you use libusb, simply set vendor- and product-ID< [plustek] ># [usb] 0x07B3 0x0017< [plustek] ># device auto< [plustek] >#< [plustek] ># NOTE: autodetection is safe, as it uses the info it got< [plustek] ># from the USB subsystem. If you're not using the< [plustek] ># autodetection, you MUST have attached that device< [plustek] ># at your USB-port, that you have specified...< [plustek] >#< [plustek] >< [plustek] >[usb] 0x04b8 0x010f< [plustek] next device is a USB device (0x04B8-0x010F) [plustek] ... next device [plustek] >device /dev/usbscanner< [plustek] Decoding device name >/dev/usbscanner< [plustek] >< [plustek] ># options for the previous USB entry< [plustek] >#< [plustek] ># switch lamp off after xxx secs, 0 disables the feature< [plustek] ># (can also be set via frontend)< [plustek] >option lampOff 0< [plustek] Decoding option >lampOff< [plustek] >< [plustek] ># warmup period in seconds, 0 means no warmup, -1 means auto-warmup< [plustek] ># (can also be set via frontend)< [plustek] >option warmup 180< [plustek] Decoding option >warmup< [plustek] >< [plustek] ># 0 means leave lamp-status untouched, not 0 means switch off< [plustek] ># on sane_close< [plustek] ># (can also be set via frontend)< [plustek] >option lOffOnEnd 0< [plustek] Decoding option >lOffOnEnd< [plustek] >< [plustek] >#< [plustek] ># options to tweak the image start-position< [plustek] ># (WARNING: there's no internal range check!!!)< [plustek] >#< [plustek] ># for the normal scan area< [plustek] >#< [plustek] >option posOffX 0< [plustek] Decoding option >posOffX< [plustek] >option posOffY 0< [plustek] Decoding option >posOffY< [plustek] >< [plustek] ># for transparencies< [plustek] >option tpaOffX 0< [plustek] Decoding option >tpaOffX< [plustek] >option tpaOffY 0< [plustek] Decoding option >tpaOffY< [plustek] >< [plustek] ># for negatives< [plustek] >option negOffX 0< [plustek] Decoding option >negOffX< [plustek] >option negOffY 0< [plustek] Decoding option >negOffY< [plustek] >< [plustek] >#< [plustek] ># for setting the calibration strip position< [plustek] ># (WARNING: there's no internal range check!!!)< [plustek] ># -1 means use built in< [plustek] ># (can also be set via frontend)< [plustek] >option posShadingY -1< [plustek] Decoding option >posShadingY< [plustek] >option tpaShadingY -1< [plustek] Decoding option >tpaShadingY< [plustek] >option negShadingY -1< [plustek] Decoding option >negShadingY< [plustek] >< [plustek] >#< [plustek] ># to invert the negatives, 0 disables the feature< [plustek] >#< [plustek] >option invertNegatives 0< [plustek] Decoding option >invertNegatives< [plustek] >< [plustek] >#< [plustek] ># to disable the internal sensor speedup function,< [plustek] ># 1 disables the feature< [plustek] >#< [plustek] >option disableSpeedup 0< [plustek] Decoding option >disableSpeedup< [plustek] >< [plustek] >#< [plustek] ># to save/restore coarse calibration data< [plustek] ># (can also be set via frontend)< [plustek] >option cacheCalData 0< [plustek] Decoding option >cacheCalData< [plustek] >< [plustek] >#< [plustek] ># use alternate calibration routines< [plustek] >#< [plustek] >option altCalibration 0< [plustek] Decoding option >altCalibration< [plustek] >< [plustek] >#< [plustek] ># for skipping whole calibration step< [plustek] >#< [plustek] >option skipCalibration 0< [plustek] Decoding option >skipCalibration< [plustek] >< [plustek] >#< [plustek] ># for skipping entire fine calibration step< [plustek] ># coarse calibration is done< [plustek] >#< [plustek] >option skipFine 0< [plustek] Decoding option >skipFine< [plustek] >< [plustek] >#< [plustek] ># discard the result of the fine white calibration< [plustek] >#< [plustek] >option skipFineWhite 0< [plustek] Decoding option >skipFineWhite< [plustek] >< [plustek] >#< [plustek] ># some scanners have a dark calibration strip, in< [plustek] ># general this one should be used for calibration.< [plustek] ># As this could cause some trouble, this option< [plustek] ># overrides that and the dark calibration will be< [plustek] ># done by switching the lamp off< [plustek] >#< [plustek] >option skipDarkStrip 0< [plustek] Decoding option >skipDarkStrip< [plustek] >< [plustek] ># for replacing the gain values found during coarse< [plustek] ># calibration< [plustek] ># (can also be set via frontend)< [plustek] >option red_gain -1< [plustek] Decoding option >red_gain< [plustek] >option green_gain -1< [plustek] Decoding option >green_gain< [plustek] >option blue_gain -1< [plustek] Decoding option >blue_gain< [plustek] >< [plustek] ># for replacing the offset values found during coarse< [plustek] ># calibration< [plustek] ># (can also be set via frontend)< [plustek] >option red_offset -1< [plustek] Decoding option >red_offset< [plustek] >option green_offset -1< [plustek] Decoding option >green_offset< [plustek] >option blue_offset -1< [plustek] Decoding option >blue_offset< [plustek] >< [plustek] >#< [plustek] ># for replacing the default lampoff settings, this< [plustek] ># works only for CIS devices like CanoScan LiDE20< [plustek] ># (can also be set via frontend)< [plustek] >option red_lampoff -1< [plustek] Decoding option >red_lampoff< [plustek] >option green_lampoff -1< [plustek] Decoding option >green_lampoff< [plustek] >option blue_lampoff -1< [plustek] Decoding option >blue_lampoff< [plustek] >< [plustek] >#< [plustek] ># for adjusting the default gamma values< [plustek] ># (can also be set via frontend)< [plustek] >option redGamma 1.0< [plustek] Decoding option >redGamma< [plustek] >option greenGamma 1.0< [plustek] Decoding option >greenGamma< [plustek] >option blueGamma 1.0< [plustek] Decoding option >blueGamma< [plustek] >option grayGamma 1.0< [plustek] Decoding option >grayGamma< [plustek] >< [plustek] >#< [plustek] ># to enable TPA (EPSON or UMAX, if autodetection fails)< [plustek] ># 0 means default behaviour as specified in the internal tables< [plustek] ># 1 means enable (needed for UMAX 3450)< [plustek] >option enableTPA 1< [plustek] Decoding option >enableTPA< [plustek] >< [plustek] >#< [plustek] ># model override functionality, currently only available for< [plustek] ># Mustek devices, using NSCs' vendor ID: 0x0400 and< [plustek] ># also their product ID: 0x1000 (LM9831) 0x1001 (LM9832)< [plustek] >#< [plustek] ># mov/PID | 0x1000 | 0x1001< [plustek] ># ---------------------------------------< [plustek] ># 0 (default)| BearPaw1200 | BearPaw 2400< [plustek] ># 1 | ignored | BearPaw 1200< [plustek] >#< [plustek] >option mov 0< [plustek] Decoding option >mov< [plustek] >< [plustek] >#< [plustek] ># and of course the device-name< [plustek] >#< [plustek] ># device /dev/usbscanner< [plustek] >#device auto< [plustek] >< [plustek] >#< [plustek] ># to define a new device, start with a new section:< [plustek] ># [usb]< [plustek] >#< [plustek] >< [plustek] attach (/dev/usbscanner, 0x7fff5fbfe760, 0x0) [plustek] Device configuration: [plustek] device name : >/dev/usbscanner< [plustek] USB-ID : >0x04B8-0x010F< [plustek] model ovr. : 0 [plustek] warmup : 180s [plustek] lampOff : 0 [plustek] lampOffOnEnd : no [plustek] cacheCalData : no [plustek] altCalibrate : no [plustek] skipCalibr. : no [plustek] skipFine : no [plustek] skipFineWhite: no [plustek] skipDarkStrip: no [plustek] incDarkTarget: yes [plustek] invertNegs. : no [plustek] dis.Speedup : no [plustek] pos_x : 0 [plustek] pos_y : 0 [plustek] pos_shading_y: -1 [plustek] neg_x : 0 [plustek] neg_y : 0 [plustek] neg_shading_y: -1 [plustek] tpa_x : 0 [plustek] tpa_y : 0 [plustek] tpa_shading_y: -1 [plustek] red gain : -1 [plustek] green gain : -1 [plustek] blue gain : -1 [plustek] red offset : -1 [plustek] green offset : -1 [plustek] blue offset : -1 [plustek] red lampoff : -1 [plustek] green lampoff: -1 [plustek] blue lampoff : -1 [plustek] red Gamma : 1.00 [plustek] green Gamma : 1.00 [plustek] blue Gamma : 1.00 [plustek] gray Gamma : 1.00 [plustek] --------------------- [plustek] usbDev_open(/dev/usbscanner,0x04B8-0x010F) - 0x100166920 [plustek] sanei_usb_open failed: No such file or directory (2) [plustek] open failed: -1 [plustek] sane_get_devices (0x7fff5fbff0b8, 0) scanimage: no SANE devices found [plustek] sane_exit |
|
